BUY FAKE PASSPORT ( realfakedocs@live.fr ) DRIVING LICENCE FALSE , FALSE...
BUY FAKE PASSPORT ( realfakedocs@live.fr ) DRIVING LICENCE FALSE , FALSE IDENTITY CARD (ID CARD) , FALSE, VISA,FALSE BIRTH . We are a team of professionals with many years of experience in producing...
View ArticleMCP1640 very hot (dragondgold)
Hello I recently bought a few MCP1640T-I/CHY. I am using them to get 5v from 3.7v when using li-po battery or 4.5v when using USB (4.5v because of a diode). This is the schematic to get 5v I am using:...
View ArticleBuy fake authentic documents (businessteam123@yahoo.com) (stacymoon098)
businessteam123@yahoo.com Buy fake authentic documents Buy a fake passport, fake visas, fake driving license, fake birth certificate, fake ID Card and many other fake DOCUMENTS...
View ArticleControl Register Bits to match LCD controller (MicroCNC)
Hello: Does any one has some code samples in SPI mode how to do this?. LCD has ST7565R controller and I need to make sure these rules are follow see the attachment. I have no money to offer you so I...
View ArticleBUY A TRUE FALSE PASSPORT ( forasia447@gmail.com ) DRIVING LICENCE / CARD (...
BUY A TRUE FALSE PASSPORT ( forasia447@gmail.com ) DRIVING LICENCE / CARD ( ID) , VISA false , fake birth. forasia447@gmail.com We are a team of professionals with years of experience in the...
View ArticleMCP3421 one cell lipo fuel gauge (exapod)
Hi, i want to use the MCP3421 18 bit ADC as a basic fuel gauge for a one cell lipo. If i connect the VIN- to my ground the max voltage that i can read is 2.048 V, a fully charged lipo is 4.1V, i was...
View ArticleMCP73842 to charge a 7.2V battery (chstr23)
Hello, I have to design a circuit to charge a battery. I would like to use a battery with this characteristics: Chemistry: Lithium IonVoltage: Vmax=8.4V Vnom=7.2 V Vcutoff=4.8VMax Continuous Power...
View ArticleMCP6546 (klaas)
Hi guys, I want to use the MCP6546. The supply voltage will be Vdd=5V and Vss=0V. During power up and power down the input voltage can exceed the rails. Input voltage is always > -0.5V and < 5V....
View ArticleMCP617 op amp problem (mshh)
i used to amplify 0-8 millivolt signal from sensor the non inverting amplifier is working well with a signal larger that 1.5 mv but for less that that value the output is bigger that expected i tried...
View ArticleMCP2515 Standalone CAN Controller and Cyclone-IV FPGA interface problem...
Hi, I m using MCP2515 Stand alone CAN Controller and its interface with Cyclone-IV FPGA (EP4CE55 484 BGA Package) via voltage translator SN74ALVC164245DL. SO pin of MCP2515 is not
View ArticleMCP2200 USB INTERFACE PROBLEM (unnati)
hi, i am using MCP2200 chip for USB interface on my device. the problem is everytime the new device is connected to WINDOWS, a new com port is assigned to the device and the driver has to be installed...
View ArticleMCP6273 Pins 1 and 5 - Ground or leave floating, please? (Organic)
Hello All. I am using an MCP6273 as a buffer. In the device's datasheet, Pins 1 and 5 are designated as "NC". Normally, I ground all unused pins in an op amp. - Is it advisable to ground Pins 1 and 5...
View ArticleAccess Denied Test Post (JANickerson)
I seem to have been denied access trying to reply to http://www.microchip.com/forums/fb.ashx?m=780180
View Article0.1 uF Decoupling Cap (floyd)
Dear Sir, I have some doubts on the use of Decopling Capacitors I am studying in my last year of graduation we are doing a project on Burglar Alarm we have used one IR transreceiver for detection. I am...
View ArticleMCP2120 parity bit (Pantelis1969)
Hello, I am trying to use MCP2120 to send serial data but with parity (Even) bit enable. It seems that there is a problem (please see the attachment file) Ch1 is the input to the MCP2120 Ch2 is the...
View ArticleMCP2210 HID DLL programming examples. Other compilers? (danpeirce)
I have received a couple of the MCP2210 demo kits and really like the little boards. It would be nice to see some programming examples that are not .NET related. I have spent a lot of time using the...
View ArticleMCP617 current sensing (mshh)
i used MCP617 to sense current , i used the configuration in the attached file while Rf=1 KΩ , RG=20 Ω and Rsense is existed in this link i think its value is around 6 m Ω .Gain should be Rf/RG =...
View ArticleMCP73871 - PROG2, TE, CE Pins (brad.young)
Hello All, I am looking to implement a MCP73871 into my design. The device will primarily be powered and recharged by USB, but needs to be able to run on the battery when its disconnected. The MCP73871...
View ArticleIC for TV booster by Microchip (micropad)
Dear All Any one would please advice me about IC that introduce by Microchip used booster for TV signal Thanks in advance..
View ArticleWhy are the Microchip forums targets of off topic spam? (dan1138)
The topic of my post is rhetorical. So why are the Microchip forums targets of off topic spam? The most obvious is that these forums are popular, active and allow any user to post links to anywhere on...
View Article